![]() I’ve used common imaging tools like clonezilla, drive image xml, shadow protect, gparted, acronis, n-able backup, etc. However, my research on what tools to use for this on drive from a Synology NAS have not been successful. Your new NAS may have different voltage requirements so use the new power supply (PSU). Performing migration moves data or drives from one Synology NAS to another. Of course, I will also need to expand the available partition size from the 10TB to the full capacity of the 18TB as well. Power down your existing NAS and swap the drives into the new unit. Before you start 1.1 Source and destination Synology NAS. Is there a way to clone or image the 10TB drive to one of the new 18TB drives. Now go to your Synology NAS and remove the failing drive and replace it with a new hard drive. Then when I add the 2nd new 18TB drive it too would only have the 10TB space available (then I would have two 18TB drives installed with only 10 TB of space - and that’s no better than where I started) This guide will walk you through how to upgrade from an old Synology NAS drive to a new one. If I were to enable data protection it would remove 8TB of the new 18TB drive leaving me with only the 10TB space available. Hardware How do I upgrade a Synology NAS drive 6 Min Read Synology NAS drives are terrifically versatile machines, but if yours is showing its age and you fancy one with a little more punch, today is your day. I’ve researched the following scenarios and have yet to find confidence on a procedure.Īdd one of the 18TB disks as a second drive in the Synology but that would only add the 18TB as additional available space - making 28TB available with no data protection. I need to upgrade this to two 18TB drives. Note: To restore drive indicator status, go to Storage Manager / Go to the HDD/SSD tab / Action / Switch Drive Indicator Status/ click Restore.I am looking for advice on upgrading a Synology DS218+ that currently has only one 10TB drive. Note: You cannot switch the status of drive indicators on cache devices since there is no indicator on such devices. When the orange led is on, you are free to change your faulty disk and insert a new one without having to turn off your NAS. ![]() Before “Switch Drive Indicator Status”.Click Switch to switch drive indicator status.Set the amount of time the drive indicator remains “alert” for, which can be between 1 minute and 60 minutes.Follow the instructions in the image below. Select a drive and click Action, then click Switch Drive Indicator Status.The status of your storage pool should be Degraded. Replacing an existing drive with a larger drive allows the storage pool capacity to be expanded. Replacing a defective drive with a healthy drive can prevent a storage pool from becoming degraded. Step 3 Open Migration Assistant on your destination NAS and follow the wizard. You can use the Replace Drive feature to replace a drive in your Synology NAS to prevent storage pool degradation or expand the storage pool capacity. (Daily, weekly monthly) Then you realise that you shouldnt really change it from data protection mode as this is a. Step 2 Create a storage pool on your destination that is equal to or larger than the storage pool on your source. Confidently upgrade your NAS performance with the assurance of a 3-year limited. Step 1 Install Migration Assistant on your destination NAS. Follow the instructions in the image below. Go to HDD/SSD to make sure the new drive is recognized. Built and tested for up to 8-bay NAS systems, these drives give you the. Please Support My work by Making a Donation. Below are step by step instructions on how to change an SSD/HDD disk if your NAS is turned on. The green triangle LED on your NAS will turn orange after this operation. In the DSM operating system there’s an option called “ Switch Drive Indicator Status” which allows you to “sleep” a disk and safely remove it. Your selected RAID system needs to be tolerant of the hot swap by having 1 or 2 disc redundancy. ![]() Your DS model’s tech specs will tell you whether it supports hot swapping or not. What is Hot Swap? Some models (generally not the budget-friendly models) allow you to pull and replace a disk while the system is powered on, which is useful if you want to swap a disk without any downtime. If you use your NAS as a web server or for hosting websites (like I do with ), you’ll find it very useful to know how to change a disk without having to turn off your NAS and, therefore, avoiding having downtime on your website. If you need to Hot Swap a hard drive on your NAS, you can use the drive indicator light on the front of your NAS to identify which drive needs replacing. If you have set up RAID 1 or 5, what you will read below should help you. Sometimes you have to change a faulty SSD/HDD disk on our Synology NAS.
0 Comments
Leave a Reply. |